- Oil supply via the tractor’s hydraulic
- Mechanical arm geometry
- 155° turn of arm – attachment tool in the the driver’s field of vision
- Wide range of tools, for example quadsaws, cutterbars, and rotary hedge cutters
Twiga BASIC Reach Mower
Twiga BASIC is build using the same principle as the Twiga FLEX but without the pump station and Rotor Flex. The Twiga BASIC uses the oil supply from the tractor. A wide variety of attachment tools to Twiga Basic can be used for grass mowing or hedge trimming.
Today, most tractors hydraulic systems are so powerful that there is enough hydraulic capacity to operate a cutterbar or a quadsaw. Hydraulic connection required with Danfoss: 1 x double acting and 1 x return flow + 1 x drain. Without Danfoss - Contact GreenTec.
Twiga BASIC has a 140º/155º arm slew.
It is available in two variants: Basic front and Basic rear mounted.
Vertical reach up to 9.3 m. with quadsaw.
In order to distribute the oil from the tractor while operating the arm we recommend mounting of Danfoss control. This is available in two variants: One to the tractor with load sensing hydraulic system and one with a normal hydraulic system.
Danfoss is equipped with joystick operation mounted on the armrest of the tractor. The benefits of this is that the control of the entire machine can be operated by one hand, providing comfortable working conditions.
|Reach horizontal*||5.6 m||6.3 m||7.1 m|
|Reach with telescopic arm||-||7.1 m||-|
|Reach vertical*||6.3 m||7.2 m||8.1 m|
|Reach vertical with telescopic arm||-||8.1 m||-|
|Transport width||2.5 m||2.5 m||2.5 m|
|Weight without tool||750 kg||800 kg||920 kg|
|Weight with telescopic arm||-||920 kg||-|
|Min. tractor requirement||4,500 kg||5,000 kg||-|
|Technical||7000||7000 LR||7000 T||7000 LRT|
|Reach horizontal*||6.7 m||7.5 m||7.9 m||8.9|
|Reach with telescopic arm||7,9 m||-||-||-|
|Reach vertical*||8.3 m||8.5||8.9||9.3|
|Reach vertical with telescopic arm||8,9 m||-||-||-|
|Transport width||2.5 m||2.5 m||2.5 m||2.5|
|Weight without tool||1,150 kg||1,205 kg||1,300 kg||1,370 kg|
|Weight with telescopic arm||1,300 kg||-||-||-|
|Min. tractor requirement||6,000 kg||-||-||-|
* Reach varies depending on working tool
|Mechanical arm geometry with APS|
|140º /155º hydraulic arm rotation with Power Steering|
|Three point stabilization|
|Cat. 2 three point linkage|
Cut and pulverize in a single pass, with a working width of 2.3 m
Cut and chop in a single pass, with a working width of 1.6 m
Quadsaw with a working width of 1.6 m
Quadsaw with a working width of 2 m.
Quadsaw with a working width of 2.4 m
Extremely powerful and effective heavy duty cutterbar for hedge cutting
Heavy duty cutterbar for hedge cutting
Cutterbar for maintenance of hedges and fences
Used for grass mowing in "hard to reach" areas
- Rear mounted
- Front mounted
- Reverse mounted
AHS (automatic obstacle control):
In case of accidental collision of obstacles, the arm will be lifted up and turns backwards. When the obstacle is passed the arm will turn back to the starting point. AHS can be detach from the cabin which gives the opportunity to turn the arm up to 90° backwards.
Parallel arm geometry
Mechincal parallel lead is standard on the Twiga Basic. The operation of machine is easier and you only have to operate a valve to change the reach.
The build of the arm
The arm is built in 6/8 mm spring steel with an eye on optimal strength in proportion to the material use. When there is a use of extra strength the arm is stronger build and there is lamellas as inside strengthening to reduce the wrench.
Floats (extra equipment)
For Verge mowing float on arm and head is hightly recommended.